Installing or Replacing a standard control panel on a SWF embroidery machine

How do I replace and install the control panel on a SWF Standard Commercial Embroidery Machine? Here is a training video that can help you with installing or replacing your control panel on your standard machine. This control panel is different than the embroidery machine LCD control panel that is popular now. Every embroidery machine had a control panel that controls the machine and they may look different but actually have most of the same functions. All embroidery machines control panels including Tajima, SWF, HAPPY, Melco and Toyota embroidery machines and at least a LED read out or a LCD readout. Even if you have a SWF compact machine or a new machine with the LCD control panel, all of the functions are the same as the standard, you just have the bonus of seeing your design sew. The Embroidery Machine Training DVD set could really help you understand these functions because it's not about "where the buttons are" it's about "what these button do!!"

Embroidery Training Videos for Service, Repair and Business

Installing or Replacing an SWF standard control panel on your Embroidery Machine

What are some helpful tips to understanding my embroidery machine control panel?

Even if you have a SWF compact machine or a new machine with the LCD control panel, all of the functions are the same as the standard, you just have the bonus of seeing your design sew. The Embroidery Machine Training DVD set could really help you understand these functions because it's not about "where the buttons are" it's about "what these button do!!" There is so much to know inside this control panel that even if you have a LCD model, this DVD set will really get you understanding your machine and in the long run......make you more money!!
Greasing the rail, Oiling the Rotary Hook, Error 100, Removing the pressure foot, Rotary hook preparation, Your machine upon arrival, Attaching or changing the control panel, Putting on the leveling bolts, Assembling the light fixture, Placement of the table, Assembling the thread rack, Pull through method, Centering the hoop, Hooping for front and side embroidery, LED PANEL,Intro to the Edit button, Cleaning bobbin case, Oiling the rotary hook, SWF machine training videos, SWF Repair Training

Back to Home

The Control Panel

Back to Chapter List

SWF 601C/1501/1501C/1502/1504/1204/1506
SWF 1501 Replacing or Installing the control panel

SWF Machine Training
DVD

SWF Repair Training
DVD set

Learn how to use your new or used SWF embroidery machine with this comprehensive, embroidery training video Learn how to Repair and Maintain your new or used SWF embroidery machine with this comprehensive training video

$99

$139

Lots of Free Videos Samples

Lots of Free Videos Samples

Fill out the form below
(for more information or to ask a question)

Email Address:

Question:

How do I LOAD a design?
Insert the design disk into the floppy disk drive. The floppy disk drive is located on the right side of the control panel.
Press the EMB.CALL button or (IN-OUT button)
Press the green DOWN button on the LCD menu indication screen to access the FDD CALL command.
Press the SET button. The machine will display all of the designs located on the floppy disk.
Scroll to the desired design name by using the green UP or DOWN button on the LCD menu indication screen.
Press the SET button. The line SELECT EMPTY ROOM will appear on the screen followed by a number. Unless a change is necessary, press the SET button.
How do I put in my basic setting?
Go to 1. BASIC SETTING
Press the SETTING button. Using the DOWN key to 3. Angle the input 0-for Flat and 180- for Caps.
Press the SET button.
How do I put in my needles (colors for design)?
Go to 2. NEEDLE SETTING
Press the SETTING button. Input needle number using number keys.
Press the SET button.
Press the SET button.
How do I ROTATE my design?
Load the design as normal. Press the SETTING button.
Press the DOWN button on the LCD menu indication screen twice to access the ANGLE command.
Press the SET button.
Change the setting by typing in the desired angle; i.e. 180. Press the SET button.
Press the PREVIOUS button.